If your dog’s bowls are elevated, it is easier to keep the feeding area clean. If your dog’s bowls are elevated, it makes it easier for you to give them food and water. Older people may have problems with arthritis and have difficulty bending over. By elevating your dog’s bowls, you will allow your dogs to be in a more comfortable position that will help with digestion.īy elevating your dog’s bowls, you are making them easier for you to reach. Laying down and eating can cause problems with digestion. When they lay down, this is putting them in a more relaxed position to eat. If your dog is lying down when they are eating, this is usually the first sign that their bowls are not high enough. Neater Pets makes a slow feeder bowl that is also elevated and is a great choice for and elevated dog bowl for dogs who eat very fast. Also, slow feeder bowls are great to use with dogs who tend to eat very fast. This can slow them down when eating because they have to eat at a more upright position. When you elevate their bowls, it makes swallowing much easier.ĭogs who are known to eat fast can benefit from an elevated bowl. When your dog has to bend over to drink water or eat food, they have to move food and water against gravity up the esophagus into the stomach. By elevating your dog’s bowls, it will help food move down their esophagus easier.Įlevated dog bowls will help with swallowing. Certain Medical Conditions Require a Raised BowlĬertain medical conditions, such as megaesophagus, can cause your dog to need elevated dog bowls.Having to bend over to eat and drink constantly can be very painful. Older dogs usually have arthritis and joint pain. When you elevate your dog’s bowls, you are helping to make them more comfortable when they are eating. Bending over all the time drinking water and eating food from bowls on the floor can cause bad posture that can lead to back problems in your dog. When you raise your dog’s bowl, you will help improve their posture. While this may be fine for some dogs, there are many reasons that a dog would benefit from a bowl that was a little higher up. When many people think of dog bowls, they see two bowls sitting on the ground. Elevated dog bowl stands are also great to keep water and food bowls together on one feeder, instead of having two separate bowls sliding around on the floor.Īn elevated dog bowl is just like it sounds it is a dog bowl that is raised off the ground. Elevated dog feeders make your dog’s food closer and easier to eat, so a lot of dogs tend to prefer them. They come in a variety of sizes, so they’re useful for both toy-sized and large-sized dogs. See last two photos above.Also known as elevated dog feeders, elevated dog bowls are simply dog bowls raised from the floor with a stand of some sort to keep it elevated. Note that I will only cut that inside hole. I also went ahead and traced out the bowl dimensions. However, I wouldn't leave any sharp nails sticking out that might scratch you or your pet. These just go with the rustic look of the pallet boards. In my opinion, it’s okay to keep some leftover nails (or nail holes) in place, as long as you’re not sawing into any nails. This is one of the downsides of using pallet wood or reclaimed wood. You don’t want your blade hitting any metal, so do be careful. Most of the time, I can eyeball this, but I also have a handheld metal detector that comes in handy for locating nails in the wood. Then I cut all the boards to make sure their lengths matched perfectly.īefore cutting, I would inspect the board for any leftover or embedded nails. Since the sides were already straight, I first cut a little off the ends so I could measure from an end that was already squared up. However, you are taking some slight risks with any pallets because you don’t know for sure what’s been stored on them or what environment they’ve been sitting in. Based on my research the heat treated ones are probably the safest to use from a health standpoint. I recommend using pallets that have an HT stamped on them which indicates they were heat treated. I will also use the jigsaw for a few curved cuts. The only cuts I will be making are crosscuts with the miter saw - no rip cuts on the table saw. I also chose boards that were very straight on the edges. I used two boards for the top that would accommodate our two dog bowls. From the good pile, I selected some that happened to be 5.25 in. I went through all the boards and culled out ones that were badly warped or cracked. That way, the boards have a better chance of matching for future projects I attempt. I had recently taken apart a couple pallets, and I kept the boards for each pallet together.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |